联系Z6尊龙官方网站官网入口
Z6尊龙官方网站官网入口
联系人：林经理
电话：151 6888 2846
邮箱：527800164@qq.com
地点：济南市历下区化纤厂路8号3号楼101号
卷帘门尺寸几多参考介绍
卷帘门适用于种种商店和、宾馆、银行医院、学校、机关、厂矿、趁魅站、码头、货仓、变电室及工业厂房等装璜设施 。卷帘门窗启闭通常接纳手动、电动兼手动或自动开启方法，正常情况下门窗电动，遇临时停电或其它情况则手动开闭 。下面来讲讲卷帘门尺寸几多吧 。
Roller shutter doors are suitable for all kinds of shops and shopping malls, hotels, banks, hospitals, schools, institutions, factories and mines, stations, wharves, warehouses, transformer rooms and industrial plants and other decoration facilities. The rolling shutter doors and windows are usually opened and closed manually, electrically and manually or automatically. Under normal circumstances, the doors and windows are electrically operated, and in case of temporary power failure or other circumstances, they are manually opened and closed. Now let's talk about the size of roller shutter door.
卷帘门尺寸：
Roller shutter door size:
1、防火卷帘门的装置分为内装和外装，h:代表洞口高；w:代表洞口宽 。内装尺寸盘算公式：w×（h+预卷＋封箱)×单价 。外装尺寸盘算公式：w×（h+外跨尺寸+预卷＋封箱)×单价 。说明：外跨尺寸：0.4m、预卷：0.6m 。
1. The installation of fireproof rolling shutter door is divided into internal installation and external installation, h: represents the height of the opening; w: Represents the opening width. Calculation formula of interior dimension: W × (h+ pre roll + box sealing) × Unit Price. Calculation formula of external dimension: W × (h+ outer span size + pre winding + sealing box) × Unit Price. Note: outer span size: 0.4m, pre roll: 0.6m.
2、防火卷帘门封箱分为：三面和二面 。三面封箱：高度要加1.6m，二面封箱：高度要加1.0m 。例如：洞口尺寸为：3m*2m 。内装二面封箱面积为：3×（2＋0.6＋1.0）＝10.8平米 。外装二面封箱面积为：3×（2＋0.4＋0.6＋1.0）＝12平米 。
2. The sealing box of fireproof rolling shutter door is divided into three sides and two sides. Three side sealing: the height should be increased by 1.6m, and two side sealing: the height should be increased by 1.0m. For example, the opening size is 3m*2m. The sealing area of two sides inside is: 3 × (2 + 0.6 + 1.0) = 10.8 square meters. The sealing area of the external two sides is: 3 × (2 + 0.4 + 0.6 + 1.0) = 12 square meters.
卷帘门装置注意事项：
Precautions for installation of roller shutter door:
1、按设计型号，查阅产品说明书和电气原理图 。检查产品外貌处理和零附件 。量测产品各部位基本尺寸 。检查门洞口是否与卷帘门尺寸相符；导轨、支架的预埋件位置、数量是否正确 。
1. Refer to the product manual and electrical schematic diagram according to the design model. Check the product surface treatment and accessories. Measure the basic size of each part of the product. Check whether the door opening is consistent with the size of the roller shutter door; Whether the position and quantity of embedded parts of guide rail and support are correct.
2、丈量洞口标高，弹出两导轨垂线及卷筒线 。
2. Measure the elevation of the hole, and snap the vertical line of the two guide rails and the center line of the drum.
3、将垫板电焊在预埋铁板上，用螺丝牢固卷筒的左右支架，装置卷筒 。卷筒装置后应转动灵活 。
3. Weld the backing plate on the embedded iron plate, fix the left and right supports of the drum with screws, and install the drum. The drum shall rotate flexibly after installation.
4、装置减速器和传动系统 。
4. Install the reducer and drive system.
5、装置电气拴街系统 。
5. Install electrical tie down system.
6、空载试车 。
6. No load commissioning.
7、将事先装配好的帘板装置在卷筒上 。
7. Install the curtain plate assembled in advance on the drum.
8、装置导轨 。按图纸划定位置，将两侧及上方导轨焊牢于墙体预埋件上，并焊成以体，各导轨应在同一笔直平面上 。
8. Install the guide rail. According to the position specified in the drawing, weld the guide rails on both sides and above to the embedded parts of the wall, and weld them into a body. Each guide rail should be on the same vertical plane.
9、装置水幕喷淋系统，并与总控制系统连接 。
9. Install the water curtain spray system and connect it with the main control system.
10、试车 。先用手去试运行，再用电动机启闭数次，调解无卡住、阻滞及异常噪音等现象为止 。全部调试完毕，装置防护罩 。
10. Commissioning. Test run by hand first, and then open and close the motor several times until there is no jamming, blocking, abnormal noise and other phenomena. After all commissioning, install the protective cover.
11、装置防护罩 。济南卷帘门卷筒上的护罩可做成方形，亦可做成半圆形 �；ふ值某叽缇尴赣τ朊诺目矶群兔盘醢寰砥鸷蟮闹本断嗍视�，包管卷筒将门条板卷满后与护罩仍坚持一定的距离，不得相互碰撞，经检查无误后，再与护罩预埋件焊牢 。
11. Install the protective cover. The shield on the drum of Jinan roller shutter door can be made into a square or a semicircle. The size of the shield should be consistent with the width of the door and the diameter of the door slat after it is rolled up, so as to ensure that the drum still keeps a certain distance from the shield after the door slat is rolled up, and shall not collide with each other. After inspection, it can be firmly welded with the embedded parts of the shield.
What is the size of the roller shutter door? The above is the relevant content of the problem, for reference only, you can consider it according to your actual situation. For more information, please come to the website for consultation Understand.
下一篇：卷帘门怎么装置更为合适科学 上一篇：选购卷帘门需要从基础部件认识起
阅读/ Recommended reading
- 济南卷帘门10 2024-12-03
- 车库卷帘门故障及维修要领 2024-12-14
- 车库卷帘门的维修和保养要领有哪些 2024-12-07
- 济南卷帘门：门锁上了该怎么解锁？ 2024-11-23
- 济南卷帘门：断掉一片后的处理要领，你学会了吗？ 2024-11-19
- 如何延长卷闸门的寿命 2024-11-06
- 重视卷帘门门口堆物问题 2024-11-06
- 快速卷帘门介绍与快速卷帘门质料说明 2024-10-26
济南卷帘门的事情原理及装置维修
2024-12-18
济南卷帘门在家庭、商业和工业建筑中获得了广泛应用，其功效齐全、可靠、美观实用的特点使其成为门窗装饰的质料 。济南卷帘门接纳高强度铝合金质料，具备抗风、抗撞击和防盗特性，并配备...
