联系Z6尊龙官方网站官网入口
Z6尊龙官方网站官网入口
联系人：林经理
电话：151 6888 2846
邮箱：527800164@qq.com
地点：济南市历下区化纤厂路8号3号楼101号
� ？鼐砹泵诺牡啥狭嗽趺葱薷� ？
济南� ？鼐砹泵�的弹簧断了怎么修复 ，以下是操作要领
How to repair the broken spring of the remote control shutter door? Here are the operation methods
扭簧的装置要领是：用手抓住扭簧的外壳 ，面对人的时候（从正面）再向上抓。
The installation method of the torsion spring is as follows: first grasp the shell of the torsion spring by hand, and then grasp it upward when facing people (from the front).
左手握紧扭簧 ，然后右手用扳手卸下牢固在门体上的螺丝（松松） ，然后用双手慢慢卸下。慢慢松开弹簧 ，直到没有阻力为止 ，以此类推各。
Hold the torsion spring with your left hand, and then use your right hand to remove the screws (loose) fixed on the door body with a wrench, and then slowly remove them with both hands. Slowly release the spring until there is no resistance, and so on.
然后把手动横梁两侧的卷靠（横梁）螺丝卸下来 ，然后把它拿下来 ，再把手动� ？鼐砹泵诺牡陕菟啃断吕� ，然后把新的也凭据卸下来的厦门弹簧设置好 ，虽然牢固螺丝也是凭据老步伐都装置好后。
Then remove the roll back (cross beam) screws on both sides of the manual cross beam, then remove it, then remove the spring screws of the manual remote control rolling shutter door, and then set the new ones according to the removed Xiamen spring. Of course, the fixing screws are also installed according to the old method.
现在要拧紧弹簧了 ，这是要害的操作（其实之前拆的时候是反偏向的）。将弹簧拧紧到需要的阻力 ，然后更换螺丝。
Now it's time to tighten the spring, which is the key operation (in fact, the previous disassembly was in the opposite direction). Tighten the spring to the required resistance, and then replace the screw.
钢叶弹簧的更换用手握住扭簧的弹簧壳面向人的偏向（从正面看） ，向上一定要握紧 ，左手握住后右手取下挂钩（如果是手动� ？鼐砹泵诺苫盗嗽蛑恍枞∠鹿夜尘托辛耍�。
To replace the steel leaf spring, first hold the spring shell of the torsion spring with your hand facing the direction of people (looking from the front), and then hold it upward. After holding it with your left hand, take off the hook with your right hand (if the manual remote control shutter door spring is broken, just take off the hook).
然后把弹簧往下拉（取下来） ，钢套必须比门体长80厘米。然后拆掉之前的螺丝 ，装置好门弹簧 ，将弹簧拧紧到佳阻力 ，挂上挂钩。
Then pull the spring down (take it off). The steel sleeve must be 80 cm longer than the door body. Then remove the previous screws, install the door spring, tighten the spring to a good resistance, and hang the hook.
其实钢弹簧和扭簧的基来源理是一样的 ，一般用户换弹簧的注意点是在使用� ？鼐砹泵攀蓖蝗焕黄鹄戳�。
In fact, the basic principle of steel spring and torsion spring is the same. Generally, users should pay attention to the fact that the spring can not be pulled up when using the remote control shutter door.
The quick solution is to find a technician to repair it, which can save unnecessary losses. Don't be smart and cause your safety to be endangered without knowledge. Come to our website for more relevant content Consult!
下一篇：防火卷帘门脱轨了怎么还原 ？ 上一篇：普通卷帘门的市场和装置要领
阅读/ Recommended reading
- 济南卷帘门的优点剖析 2024-12-16
- 济南卷帘门的装置指南：办法与注意事项 2024-12-11
- 济南卷帘门的维修保养：延长使用寿命的要害 2024-12-09
- 济南卷帘门：卷帘门� ？仄魇Я槭笔允员疚牡囊彀桑� 2024-11-16
- 电动卷帘门的优势 2024-11-12
- 济南卷帘门：卷帘门� ？仄魇Я樵趺窗� ？ 2024-09-02
- 济南卷帘门厂：卷帘门卡主了怎么办 2024-08-28
- 济南电动卷帘门：电动卷闸门没电了怎么开? 2024-08-28
车库卷帘门故障及维修要领
2024-12-23
车库卷帘门在使用历程中可能会遇到种种故障 ，以下是一些常见的故障及其维修要领： Garage rolling shutter doors may encounter vario...
